What is the issue?The potential performance of a marine VHF radio is limited by the quality of the antenna and its installation. A badly designed antenna fitted with undersized cable and imperfect connections will make the performance of even the most exquisite and expensive radio unacceptable. It is important to select the right antenna and install it in such a way that it maximises the performance of the radio to which it is attached.
Why address this?VHF communication is a critical safety resource as well as a convenient means of communication. Its range and functionality should be optimised.
How to address this?
VHF radio range is a line of sight means of communication so height is a very important factor in achieving maximum range. On a yacht, the most suitable antenna location is, therefore, at the top of the mast. Two boats, each with a masthead antenna 18 metres or 60’ above sea level can theoretically communicate at about 20 miles. A transmitter at a coast station, perhaps 1,000 feet above sea level, could communicate with these same boats at closer to 50 miles.
For those who wish to do the maths themselves the formula is: D1 + D2 (total distance between stations in nm) is equal to 1.23(0H1 +0H2), where H is the height of the antennas in feet.
Accepting that the VHF antenna must be positioned as high as possible on the boat, we can turn to other factors that will affect radio performance.
Selecting an antenna
But why choose a 3dB antenna for the masthead when you could get all that extra power from a 9dB antenna?
Well, the increased signal strength of a high gain antenna is achieved by concentrating the signal radiating from it into a narrow disc. The signal radiates at right angles to the antenna with very little radiation upwards or downwards. When the boat heels and the antenna rocks backwards and forwards the concentrated disc-like radiation pattern points the signal at the sky, or at the sea, instead of at the horizon. A 3dB gain antenna has a radiation pattern that looks more like a fat doughnut than a disc, with a significant portion of the signal radiating upwards and downwards. No matter how much the boat heels, such an antenna will still have some portion of its signal looking at the horizon and, because VHF transmissions are line-of-sight, this is vital to performance. Hence the universally accepted use of a 3dB gain antenna for boating applications, particularly for masthead mounting.
Another measure of antenna performance is the Standing Wave Ratio - SWR. This may be referred to as VSWR, Voltage Standing Wave Ratio, but it is the same thing. This is, in very simple terms, a measure of the amount of the transmission power that is lost in the antenna system. If the antenna system were perfect and the entire signal power leaving the radio was transmitted by the antenna, and its cables and connections, the SWR would be 1:1. Sadly this is not achievable, but getting as close as possible is a worthy aim. An SWR of 2.0:1 over the whole system represents a ½ dB loss in signal strength and is barely acceptable. To achieve or, preferably, better this performance the antenna itself should have the best possible SWR.
Other criteria for selecting a marine antenna, particularly one for masthead mounting, would be:
- 1/ Resistance to UV degradation. Clearly, all stainless steel construction wins hands down.
- 2/ Resistance to bird strikes. Again, a stainless steel whip is less vulnerable than a rigid plastic one.
- 3/ Ability to be removed when the mast is taken down. This is when the antenna is particularly vulnerable and those with factory crimped connections cannot be removed without removing all the cable with them. The connection at the antenna should be an SO239 socket which takes the standard PL259 connector.
- 4/ Low weight.
- 5/ Sturdy mounting bracket.
Once the antenna has been selected we can turn to the other components of the antenna system; the cable and connectors.
Marine VHF applications require 50-ohm coax. TV cable is 75 ohm and is not suitable.
Suitable cables include RG-58 (smallest), RG-8X, RG-8U and RG213. RG-213 is the same size as RG-8U but with completely waterproof and ultra-violet resistant insulation. RG-213 is more difficult to work with when it comes to making connections and is very expensive, so probably best left to super-yachts. RG58 is only suitable for interconnections between equipment and for very short runs.
Photo: Public Domain
Coax must have copper braid, preferably tinned copper braid. Braid is described by percentage figures, 98% is the best, 96% is good. It is important that the dielectric, the insulating surrounding the centre core of the cable, is solid polyethylene. Foam core dielectrics can suck moisture into the cable via the connections and cause the core and braid to corrode.
A good UV resistant cover is essential for longevity. Ancor Marine Products produces a top quality RG8X cable specifically for marine applications at a very competitive price.
Photo: Public Domain
The cable terminal is the PL259 plug. This plug fits RG8U cable and, with suitable adaptors, RG8X and RG58. The PL259 connector mates with a SO-239 socket fitted to quality antennas.
Photo: Public Domain
Connections should be soldered. Many manufacturers use pressure crimped connections but these are subject to corrosion and need special tools to create the connection - see also fitting a PL259 aerial connector to coaxial cable. Remember, you should be able to remove the antenna when the mast is taken down for winter storage.
Photo: Tony Gibson
The coaxial cable can be run inside or outside the mast. If the run is on the outside it is particularly important to have a UV resistant cover; a white exterior jacket looks less industrial on most masts than the more common black or brown cable.
If the cable is inside the mast it should be restrained to prevent tangling with halyards or other cables and to avoid the maddening rapping of the cable against the mast. Modern mast sections have inbuilt channels through which the cable can be run. Older masts should, if at all possible, have a conduit fixed inside. As a last resort, the cable can be fitted with groups of three plastic cable ties at about ten-foot intervals, with the tails of the cable ties radiating out to the interior wall of the mast. This will hold the cable off the mast wall somewhat, but will not avoid abrasion from halyards or other cables. On wooden masts, it is usual for the cable to be run externally.
Header photo with thanks to Yacht Rent
With thanks to:Salty John, specialising in a select collection of tried and tested sailing equipment. Web site: http://www.saltyjohn.co.uk/ phone +44 (0) 1995 672556 e-mail: firstname.lastname@example.org Header pho
Add your review or comment:
Please log in to leave a review of this tip.
eOceanic makes no guarantee of the validity of this information, you must read our legal page. However, we ask you to help us increase accuracy. If you spot an inaccuracy or an omission on this page please contact us and we will be delighted to rectify it. Don't forget to help us by sharing your own experience.